Home > Error Code > Image Hot Tub Error Codes

Image Hot Tub Error Codes

Contents

No action is necessary. Back to Top rtr or TREAT WOOD Message Time to "Treat Wood Reminder" (rtr).Appears Every 180 Days*. Blocked Skimmer.4. There is Not enough Water in the Heater to Start it. this contact form

Leave a Reply Click here to cancel reply. The temp sensor is the larger of the two silver bullets. OH, or OHH, or OHS (Overheat) all mean that a temperature sensor has detected unsafe water temperatures of 108° - 118° F, and your spa is in an emergency cool down Back to Top rdr or DRAIN WATER Message Time to "Drain Spa Water Reminder" (rdr).Appears Every 90 Days*. http://www.spadepot.com/spa-error-codes.htm

Balboa Hot Tub Error Codes

Sometimes, it's actually a bad pressure switch or flow switch, or loose connections or damaged wires or wire connectors. HFL = Substantial difference between temperature sensors detected. Closed Slice Valve.7.

The Heater and Pump will Operate Any time the Thermostat Demands Heat. You can follow any responses to this entry through the RSS 2.0 feed. The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. Marquis Spa Error Codes You must be logged in to post a comment.

HOT, OL, HL, FLO, Sn… SPA TEMPERATURE SENSOR ERROR CODE FLOW CHART Here's a Cal Spa troubleshooting chart for when your spa topside display shows a sensor error code Sn, Sn1, Vita Spa Error Codes Then press Temp once to exit Priming Mode. Low Water Level.2. this website Could be a dirty filter, a clogged impeller, closed valve, or a piece of plastic film covering the spa drain.

You must be logged in to post a comment. Great Lakes Hot Tub Error Codes Add Sanitizer according to Manufacturers Instructions.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never get this Message. Anmelden 10 Wird geladen... Contact your Dealer or Service Organization.

Vita Spa Error Codes

Select "Message Other than rtC or RTC FAILURE" Below. read review You can change this preference below. Balboa Hot Tub Error Codes Adding cool water may be necessary. How To Fix Flo Error Hot Tub If there is No Error Message, Select "No Error Message" Below.

The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. http://mttags.com/error-code/intellowasher-error-codes.php Back to Top rPH or CHECK PH Message Time to Check "pH Level Reminder" (rPH).Appears Every 7 Days*. You can follow any responses to this entry through the RSS 2.0 feed. FL1 = Water flow problem, inhibited or pressure switch malfunction. Hot Tub Error Code Oh

  • After about 45 Seconds, Check for Error Messages on the Topside Panel Display.
  • For Low Flow spa error codes, check the filter, check the pump and check the valves to find something that is obstructing the water flow.
  • It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing.
  • HLoH = Hi Limit Over Heat.
  • Happy Hot Tubbin' Daniel Lara Hot Tub Works Tags: spa error codes, Spa Heater Elements, spa heaters This entry was posted on Tuesday, January 6th, 2015 at 6:58 am and
  • Spa has shut down.
  • This is normal operation.
  • This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally.

Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or Back to Top drY, dY, or HEATER DRY SERVICE REQD Message There is a Verified "Dry" (drY or dY) Condition in the Heater.The "dr" or "HEATER MAY BE DRY WILL RETEST Sn2 = Nonfunctional temperature sensor. navigate here Read our FAQ!

Heater is deactivated. Coleman Spa Error Codes The Sensors are Possibly Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. Heater disabled but the spa is operational.

FL2 = Pressure switch problem.

Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. Coast Spa Error Codes Leave a Reply Click here to cancel reply.

Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. If one of these sensors needs to be replaced BOTH should be replaced at the same time. Wird verarbeitet... his comment is here Pump may also be deactivated).

Wird verarbeitet... BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. The spa obviously should not be used when OH or OHH is flashing on the topside control; as the water could be scalding hot for several more minutes.

Spa has shut down. The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. If your water flow is perfectly fine, then you could have a problem with the thermostat or high limit switches used on older spa packs, which could fall out of calibration, Wird geladen...

Eventually, the temp sensors or high limit switches will detect the increased water temperature, and shut everything down. When the water isn't flowing like it should, the heater stops working, equipment overheats and water quality quickly suffers. Here's what to do if your spa throws a FL, FLO or FLOW error code at you. Melde dich bei YouTube an, damit dein Feedback gezählt wird.

Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in If you still have problems, check over your temp sensor and hi limit circuits for wire or plug or sensor problems. OH, OHH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights Temperature Sensor Failure. This indicates a Possible Problem with the System Board.

Closed Slice Valve.7. Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Like our previous discussions on spa error codes, FLO and OH, the sensor codes Sn, Sn1, Sn2… are very much water flow dependent.

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Status of the heater element is unknown. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. Select "Message Other than PSt or PERSIST FAIL" Below.